Create a delete ADJS neighbor and make CR
Bạn đang xem bản rút gọn của tài liệu. Xem và tải ngay bản đầy đủ của tài liệu tại đây (6.67 MB, 85 trang )
CREATE A DELETE ADJS NB MAKE CR
Hiennv
1- After we get a updated neighbor file , Cell file , PRACH file , it is ready to import to MapInfo.
2- Open “ MapInfo Pro” and then click to LEGACY.
1
1: Click to “ LEGACY “
After step 1,Click at RF0406 as step 2 .You can see the button “Import” on the picture as below:
2
2: Click to “ RF0406”
To Import Cell File
To Import Neighbor File
To Import PRACH File
3- To Import Cell File to MapInfo :
Need detail
for Propetie
1
2
1: Click to “Create Cell Maps“
2: Click to “ File “
After step 2,pls do step by step to open Cell file in MapInfo as below ;
When you open the
files , you can see
files easily by
putting and linking in
this folder (RF0406).
3
5: Click to “OK”
5
* Wait a few minute ,loading to open file :
4
3: Choose Cell File
4: Click to “Open”
After loading, you can see “ Cell_3G_Map” box as below.
* Finished importing of Cell File to MapInfo :
4- To Import Neighbor File to MapInfo :
1
1: Click to “Create Neighbour
Maps“
2
2: Click to “Create Neighbor
Maps“
After step 2,pls do step by step to open Neighbour file in MapInfo as below ;
3
5: Click to “OK”
5
* Wait a few minute ,loading to open file :
4
3: Choose Neighbor File
4: Click to “Open”
After loading, you can see “ Neigh3G3GIntra_Map” box as below.
* Finished importing of Neighbor File to MapInfo :
5- To Import PRACH File to MapInfo :
1: Click to “RF0406
Beta”
1
2
After Step2,you will find one box as below ;
3
3: Click to “File”
2: Click to “Create Timing Advance
Propagation Delay Table”
After you click “File” ,the box will fall down as “Open” that you can choose “PRACH” File.
4
6: Click to “OK”
6
* Wait a few minute ,loading to open file :
5
4: Choose PRACH File
5: Click to “Open”
7: Choose ‘ Display Timing Advance
of Propagation Delay’
7
9
8
8: Click on a sector
10
9: Choose a sector
10: Click on ‘OK’
After that, you can see “ PRACH_Map” box and how it work as below.
6- Useful Commands in MapInfo
* You can put more commands as you like by doing following steps :
1
1: Click “ Arrow”
2
2: Click “ More Command..”
If you want to add more commands , you can do it in “ Customize Ribbon “ by adding ;
6
3
4
4: After do it as
step3,the command
that you want to put
on Toolbar will show
in “Quick Access
Toolbar ” box.
5
3: Do double clicks on command (or) firstly choose the
command and then click on “Add” if you want to put
and show on Quick Access Toolbar.
5: Click on “OK”
6: You can choose more command in
“ Choose Commands from”
After step 6, You can see commands on Toolbar . By doing like this ,you can see and use easily ;
7- Searching the site in Cell 3G Map:
* Press “ Ctrl + f “
2
2: Write your site name
4: Click to your site
4
1
1: Click to “OK”
3
3: Click to “OK”
4: Double Click
on it
After step 5,you will find your site with pin design.
8- About Sector :
Sector 1
Sector 3
U2100
HOS Site
U900
Sector 2
HOS Site
9- If you want to know neighbor sectors of a site, please check like below steps :
2: Choose “ Display 3G3G Intra-Frequency
Neighbors ”
2
1
3
3: After step 2, touch with it on
area of U900 of Sector 1.
4
5
1: It is U900 of Sector1 (eg:YAW7622_1)
4: After that , “Found 2 cells” box
falls down and choose the sector
number in “ Select 1 Cell”.
5: Click on ”OK”.
After step 5, you can see neighbor sectors of U900_Sector 1 (YAW7622_1).
Neighbor Sector
YAW7622_1
Neighbor Sector
Neighbor Sector
10- Neighbor Add
1
1: Choose “ Select Source Cells
for Neighbor Plan”
3
2
4
5
4: Click on ”OK”.
2: After step 1, touch with it on
area of U900 of Sector 1.
3: After that , “Found 2 cells” box
falls down and choose the sector
number in “ Select 1 Cell”.
5: You selected U900_Sector
1,So now you can start to add
neighbor .
If you want to add neighbor sector , do step by step as below.
6
6: Choose “ Select Target Cells
for Neighbor Creation “
7:If it had neighbor sector, no
need to add again.
7
8
8: Click on it to add neighbor.
9
10
11
9: After that ,you will be found
“Found 2 cells” box and choose the
sector number in “ Select 1 Cell”.
10: Click on ”OK”.
11: It is a selecting line to add
neighbor .
