Xe ô tô hyundai excel toàn tập hyundai excel - P19
Bạn đang xem bản rút gọn của tài liệu. Xem và tải ngay bản đầy đủ của tài liệu tại đây (161.55 KB, 14 trang )
REAR
SUSPENSION
Return To Main Table of Contents
GENERAL ...........................................
2
REAR SUSPENSION
................................ 6
REAR AXLE HUB
..................................
12
GENERAL
GENERAL
SPECIFICATIONS
Suspension system
Trailing arm type
Coil spring
Wire dia. x O.D. x free length mm (in.)
Spring constant N/mm (lb/in.)
Identification color
[WO P/S, 50L F/T]
10.8 x 117.8 x 293.7
(0.43 x 4.64 x 11.56)
22.5 (128.8)
Red 2 lines
[WT P/S, 50L F/T]
11.3 x 118.3 x 314
(0.44 x 4.66 x 12.36)
18.9-35.7 (108.1-203.8)
Pink 2 lines
Shock absorber
Type
Max. length
Min. length
Stroke
Damping force [at 0.3 m/sec. (0.984 ft./sec.)]
Rebound
Bound
Shock absorber identification color
Stabilizer bar O.D.
Hydraulic, cylindrical, double-acting type
390 mm (15.4 in.)
265 mm (10.4 in.)
125 mm (4.9 in.)
882 ± 137 N (194±30 lb)
588 ± 117 N (129±25.7 lb)
Red
14.5 mm (0.57 in.)
WO: Without, WT: With, P/S: Power steering, F/T: Fuel tank
SERVICE STANDARD
Camber (Standard value)
+30'
-40' -40'
TIGHTENING TORQUE
Nm
kg.cm
Ib.ft
Nuts at both ends
of
suspension arm
49-69 500-700
36-51
Fixture and body
49-69 500-700 36-51
Shock absorber
64-78 650-800 47-58
Bump stopper
18-25 180-250 13-18
Brake drum
20-0-5
200-0-50
15-0-4
55-2
GENERAL
LUBRICANTS
Recommended lubricants
Quantity
Inside of suspension arm (L.H.)
and outer periphery of suspension
arm (R.H.)
Bushing A and B
Inside of dust cover and lip
Wheel bearings, oil seal lip and inside
Inside hub cap
Multipurpose grease
SAE J310a, NLGI grade #3
Multipurpose grease
SAE J310a, NLGI grade #3
Multipurpose grease
SAE J310a, NLGI grade #3
Multipurpose grease
SAE J310a, NLGI grade #2
Mulitpurpose grease
SAE J310a, NLGI grade #2
As required
As required
As required
As required
50-60 gm
(1.8-2.1 oz)
55-3
GENERAL
SPECIAL TOOLS
TOOL
(Number and name)
09500-21000
Bar
09517-21400
Drift
09527-21000
Bearing installer
09527-21100
Bearing installer
09555-21000
Bar
09555-21100
Bushing installer
ILLUSTRATION
USE
Removal and installation of oil seal and
bearing
Removal of rear wheel bearing outer race
1) Installation of rear hub inside bearing
outer race (use with 09500-21000)
2) Installation of rear hub oil seal (use with
09500-21000)
Installation of rear hub outside bearing
outer race (use with 09500-21000)
Installation of rear suspension arm bushing
B (use with 09555-21100)
Installation of rear suspension arm bushing
A and B (use with 09555-21000)
55-4
GENERAL
TROUBLESHOOTING
Symptom
Abnormal sound
Poor ride control
Abnormal tire wear
Probable cause
Suspension securing bolt(s) loose
Loose wheel nuts
Faulty shock absorber
Worn bushings
Damaged or worn wheel bearings
Components bent or distorted
Broken coil spring
Wheel or tire unbalance
Improper tire inflation
Defective tire
Improper tire inflation
Defective tire
Loose wheel nuts
Suspension securing bolt(s) loose
Damaged or broken components
Worn bushings
Faulty shock absorber
Sagging or broken coil spring
Improper rear wheel alignment
Improper rear wheel alignment
Bent or damaged parts
Improper inflation
Wheel or tire unbalance
Loose wheel bearings
Faulty shock absorber
Remedy
Tighten to specified torque
Replace damaged parts
Balance
Inflate to specification
Replace
Inflate to specification
Replace
Tighten to specification
Replace
Replace parts
Replace parts
Replace parts
Inflation specification
Balance
Adjust or replace
Inspect and repair
55-5
