Mô hình Taj Mahal Ấn độ
Bạn đang xem bản rút gọn của tài liệu. Xem và tải ngay bản đầy đủ của tài liệu tại đây (471.46 KB, 7 trang )
Taj Mahal, India: Assembly Instructions
Canon ® is a registered trademark of Canon Inc. © Canon Inc. © A & A Co., Ltd.
Before starting assembly:Writing the number of each section on its
back side before cutting out the sections is highly recommended.
(* This way, you can be sure which section is which even after cutting out
the sections.)
/>
Indicates where sections should
be glued together.
[1] Assemble the rear, nameplate, and front sides of the stand and glue the front and rear
sides together.
* Assemble both the left and right sides in the same way.
15
1
View of completed model
*This model was designed for Papercraft and may differ from the original in some respects.
Assembly Instructions:Seven A4 sheets(No.1 to No.7)
*Build the model by carefully reading the Assembly Instructions, in the parts sheet page order.
*Hint: Trace along the folds with a ruler
and an exhausted pen (no ink) to get a sharper, easier fold.
Assembly Instructions
Mountain fold(dotted line)
Make a mountain fold.
Valley fold(dashed and dotted line)
Make a valley fold.
Scissors line(solid line)
Cut along the line.
Cut in line(solid line)
Cut along the line.
Tools and materials
Assembly tip
Caution
2
Glue
The glue spot(colored dot)
shows where to apply the glue.
Glue spot(Red dot)
16
Glue parts with the same number together.
Glue spot(Green dot)
Glue within the same part.
Glue the rear
surfaces
together.
Glue spot(Blue dot)
Glue to the rear of the other part.
Scissors, set square, glue(We recommend stick glue), pencil, used
ballpoint pen, toothpicks, tweezers, (useful for handling small parts)
Before gluing, crease the paper along mountain fold and valley
fold lines and make sure rounded sections are nice and stiff.
Glue, scissors and other tools may be dangerous to young children
so be sure to keep them out of the reach of young children.
1
Taj Mahal, India: Assembly Instructions
Canon ® is a registered trademark of Canon Inc. © Canon Inc. © A & A Co., Ltd.
12
3
11
Taj M
Agra ahal
13
, India
8
10
9
5
4
6
7
35
1
+
2
+
15
+
16
35
2
Taj Mahal, India: Assembly Instructions
Canon ® is a registered trademark of Canon Inc. © Canon Inc. © A & A Co., Ltd.
[2] Assemble the stand for the building.
17
18
3
Taj Mahal, India: Assembly Instructions
[3] Assemble the building.
Canon ® is a registered trademark of Canon Inc. © Canon Inc. © A & A Co., Ltd.
22
19
Glue all eight of these parts
together in the same way.
Flex these parts
before assembly.
23
Glue all seven of these parts
together in the same way.
21
19 - 21
19 - 21
19 - 21
Match the seams to
the positions of
the cut openings.
20
Insert the section and glue
the tabs to the reverse
side as shown in the
illustration (for all
five sections).
19 - 21
14
* The front of the hole for the central dome is its pointed side.
4
Taj Mahal, India: Assembly Instructions
Canon ® is a registered trademark of Canon Inc. © Canon Inc. © A & A Co., Ltd.
[4] Assemble the building.
26 27 28
24
Flex these parts before
assembly.
29
Fold outward.
30
Flex these parts before assembly.
27
26
28
Flex these parts before assembly.
5
Taj Mahal, India: Assembly Instructions
Canon ® is a registered trademark of Canon Inc. © Canon Inc. © A & A Co., Ltd.
25
25
[3] Building
25
25
25
[2] Building foundation
25
25
25
The front side is the side
with this protrusion.
6
Taj Mahal, India: Assembly Instructions
Canon ® is a registered trademark of Canon Inc. © Canon Inc. © A & A Co., Ltd.
[5] Assemble the four towers, glue them to the building foundation assembled in step [2], then glue these to the stand assembled in step [1].
32
Glue together at eight places,
as shown in the illustration.
31
The front side is the side
with this protrusion.
33
34
Match the seams to
the positions of the cut
openings.
l
aha
j M ndia
TaAgra, I
[1] Stand
[2] Building foundation
Finished!
7
