Tiêu chuẩn iso 01125 1999 amd1 2011
Bạn đang xem bản rút gọn của tài liệu. Xem và tải ngay bản đầy đủ của tài liệu tại đây (32.17 KB, 6 trang )
ISO
1125
Third edition
1999-03-15
AMENDMENT 1
2011-05-15
Rubber compounding ingredients —
Carbon black — Determination of ash
AMENDMENT 1: Insertion of additional item
in test report
Ingrédients de mélange du caoutchouc — Noir de carbone —
Détermination du taux de cendres
AMENDEMENT 1: Ajout d'un élément supplémentaire dans le rapport
d'essai
Reference number
ISO 1125:1999/Amd.1:2011(E)
© ISO 2011
Copyrighted material licensed to BR Demo by Thomson Reuters (Scientific), Inc., subscriptions.techstreet.com, downloaded on Nov-27-2014 by James Madison. No further reproduction or distribution is permitted. Uncontrolled when printe
INTERNATIONAL
STANDARD
COPYRIGHT PROTECTED DOCUMENT
© ISO 2011
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
Web www.iso.org
Published in Switzerland
ii
© ISO 2011 – All rights reserved
Copyrighted material licensed to BR Demo by Thomson Reuters (Scientific), Inc., subscriptions.techstreet.com, downloaded on Nov-27-2014 by James Madison. No further reproduction or distribution is permitted. Uncontrolled when printe
ISO 1125:1999/Amd.1:2011(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
Amendment 1 to ISO 1125:1999 was prepared by Technical Committee ISO/TC 45, Rubber and rubber
products, Subcommittee SC 3, Raw materials (including latex) for use in the rubber industry.
© ISO 2011 – All rights reserved
iii
Copyrighted material licensed to BR Demo by Thomson Reuters (Scientific), Inc., subscriptions.techstreet.com, downloaded on Nov-27-2014 by James Madison. No further reproduction or distribution is permitted. Uncontrolled when printe
ISO 1125:1999/Amd.1:2011(E)
Copyrighted material licensed to BR Demo by Thomson Reuters (Scientific), Inc., subscriptions.techstreet.com, downloaded on Nov-27-2014 by James Madison. No further reproduction or distribution is permitted. Uncontrolled when printe
Rubber compounding ingredients — Carbon black —
Determination of ash
AMENDMENT 1: Insertion of additional item in test report
Page 1, Clause 2
Replace the text of the clause by the following:
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 1124, Rubber compounding ingredients — Carbon black shipment sampling procedures
Page 3, Clause 8
Move the whole of the text of the clause to an informative annex (Annex A, “Precision statement”), replacing
the original Clause 8 by the following:
8
Precision
See Annex A.
Page 4, Clause 9
Insert the following item, modifying the lettering of the subsequent items accordingly:
b)
all details necessary for complete identification of the sample;
End of text
Add a bibliography containing the following informative reference:
[1]
ISO/TR 9272, Rubber and rubber products — Determination of precision for test method standards
© ISO 2011 – All rights reserved
1
Copyrighted material licensed to BR Demo by Thomson Reuters (Scientific), Inc., subscriptions.techstreet.com, downloaded on Nov-27-2014 by James Madison. No further reproduction or distribution is permitted. Uncontrolled when printe
ISO 1125:1999/Amd.1:2011(E)
Price based on 1 page
ICS 83.040.20
© ISO 2011 – All rights reserved
Copyrighted material licensed to BR Demo by Thomson Reuters (Scientific), Inc., subscriptions.techstreet.com, downloaded on Nov-27-2014 by James Madison. No further reproduction or distribution is permitted. Uncontrolled when printe
ISO 1125:1999/Amd.1:2011(E)
