STD-IS0 603-6-ENGL

4853903 0804078 92T

L979

m

INTERNATIONAL STANDARD IS0 603-1:i999
IS0 603-2:1999
IS0 603-3:1999
IS0 603-4:1999
=
W
S
IS0 603-5~1999
IS0 603-6:1999
I S 0 603-7: 1999
IS0 603-8~1999
This material is reproduced from IS0 documents under International Organization
IS0 603-9~1999
for Standardization (ISO) Copyright License Number IiiS/CC/1996. Not for resale.
I S 0 603-10:1999
No part of these IS0 documents may he reproduced in any form, electronic retrieval
IS0 603-11:1999
system or otherwise, except as allowed in the copyright law ofthe country of use, or
IS0 603-12~1999
with the prior written consent of I S 0 (Case postale 56,121 1 Geneva 20, Switzerland,
IS0 603-13:1999
Fax +41 22 734 10 79), 1HS or the IS0 Licensor's members.
IS0 603-14:1999

IS0 603-15:1999
I S 0 603-1611999

-

-

;Is07
-

TECHNICAL CORRIGENDUM 1
Published 1999-11-15
INTERNATIONAL ORGANIZATIONFOR STANDARDIZATION * MmYHAPOlU-UGì OPrAHM3wM.R ii0 CTMUlAPTM3A!JMM

ORGANISATION INTERNAllONALE DE NORMALISATION

Bonded abrasive products - Dimensions Part 1: Grinding wheels for external cylindrical grinding between centres
Part 2: Grinding wheels for centreless external cylindrical grinding
Part 3: Grinding wheels for internal cylindrical grinding
Part 4: Grinding wheels for surface grinding/peripheralgrinding
Part 5: Grinding wheels for surface gr¡nding/face grinding
Part 6: Grinding wheels for tool and tool room grinding
Part 7: Grinding wheels for manually guided grinding
Part 8 : Grinding wheels for deburring and fettling/snagging
Part 9: Grinding wheels for high-pressuregrinding
Part 1O: Stones for honing and superfinishings
Part 11: Hand finishing sticks
Part 12: Grinding wheels for deburring and fettling on a straight grinder
Part 13: Grinding wheels for deburring and fettling on a vertical grinder
Part 14: Grinding wheels for deburring and fettling/snagging on an angle grinder

Part 15: Grinding wheels for cutting-off on stationary or mobile cutting-off machines
Part 16: Grinding wheels for cutting-off on hand held power tools
TECHNICAL CORRIGENDUM 1

- Dimensions -

Partie I: Meules pour rectification cylindrique extérieure entre centres
Partie 2: Meules pour rectification cylindrique extérieure sans centres
Partie 3: Meules pour rectification cylindrique intérieure
Partie 4: Meules pour rectification planeheulage tangentiel
Partie 5: Meules pour rectification planehneulage latéral
Partie 6: Meules pour affûtage d'outils
Partie 7: Meules pour meulage à guidage manuel
Partie 8: Meules pour ébarbage et ébavurage
Partie 9: Meules pour meulage haute pression
Partie 1O: Bâtons rodoirs et de superfinition
Partie I l : Pierres à main
Partie 12: Meules pour ébarbage et ébavurage sur meuleuses portatives droites
Partie 13: Meules pour ébarbage et ébavurage sur meuleuses portatives a axe verfical
Partie 14: Meules pour ébarbage et ébavurage sur meuleuses Portatives a renvoi dangle
Partie 15: Meules pour tronỗonnage cur machines fixes ou mobiles
Partie 76: Meules pour tronỗonnage cur machines portatives
RECTIFICATIF TECHNIQUE I

ICs 25.100.70

Ref. No. I S 0 603 (parts 1 to 16):1999/Cor.l:1999(E)

O I S 0 1999 - All rights reserved
Printed in Switzerland

Copyright International Organization for Standardization
Provided by IHS under license with ISO
No reproduction or networking permitted without license from IHS

Not for Resale

--`,,`,-`-`,,`,,`,`,,`---

Produits abrasifs agglomérés


STDmISO b03-b-ENGL

L979

4853903 0804079 8bb

IS0 603 (parts 1 to 16):1999lCor.l:1999(E)

Technical Corrigendum 1 to parts 1 to 16 of International Standard IS0 603 was prepared by Technical Committee
ISO/TC 29, Small tools, SubcommitteeSC 5, Grinding wheels and abrasives.
--`,,`,-`-`,,`,,`,`,,`---

Page i¡¡
Foreword

Paragraph 5, replace the reference to I S 0 3290:1976 by IS0 3920:1976.

O IS0 1999 - All rights reserved


2

Copyright International Organization for Standardization
Provided by IHS under license with ISO
No reproduction or networking permitted without license from IHS

Not for Resale


--`,,`,-`-`,,`,,`,`,,`---

IS0
603-6

INTERNATIONAL
STANDARD

First edition
t 999-07-15

Bonded abrasive products
Dimensions -

-

Part 6:
Grinding wheels for toot and tool room grinding
Produits abrasifs agglomérés - Dimensions Partie 6: Meules pour affûtage d'outils

This material Is reproduced from IS0 documena under InternationalOrganization for

Standardization (60)
Copyright License Number IHS/ICUI 996. Not for resale. No
part of these I S 0 documents may be reproduced in any form, electronic retrievalw e m
or otherwise, except as allowed in the copyright law of the country of use, or with the
prior written consent of IS0 (Case postale 56, 121 i Geneva 20, Swiuerland, Fax +41
22 734 10 79), IHS or the I S 0 Licensor's members.

Reference number
IS0 603-61999(E)
Copyright International Organization for Standardization
Provided by IHS under license with ISO
No reproduction or networking permitted without license from IHS

Not for Resale


STD-IS0 b03-b-ENGL

1999

E 4851903 0790071 150 111

I S 0 603-6:1999(E)

Contents

Page

1 Scope ........................................................................................................................................................................


1

2 Normative references ..............................................................................................................................................

1

3 Dimensions............................................................................................................................................................... 2
3.1 Type 1: Straight grinding wheel (general application)......................................................................................

2

3.2 Type 3: Wheel tapered on one side ..................................................................................................................... 2
3.3 Type 5: Wheel recessed on one side ..................................................................................................................

3

3.4 Type 7: Wheel recessed on both sides............................................................................................................... 3
3.5 Type 1: Straight grinding wheel (saw sharpening) ...........................................................................................

4

................................................................................................................................... 5
5
3.7 Type 11: Taper cup wheel ....................................................................................................................................
3.8 Type 12: Dish wheel.............................................................................................................................................. 6
4 Designation ..............................................................................................................................................................
6
5 Specifications...........................................................................................................................................................
7
5.1 Tolerances.............................................................................................................................................................

7
5.2 Balancing...............................................................................................................................................................
7
5.3 Marking .................................................................................................................................................................. 7
8
Bibliography................................................................................................................................................................
--`,,`,-`-`,,`,,`,`,,`---

3.6 Type 6: Straight cup wheel

8 I S 0 1999
All rights reserved. Unless otherwise specified. no part of this publication may be reproduced or utilized in any form or by any means. electronic
or mechanical. including photocopying and microfilm. without permission in writing from the publisher.
International Organization for Standardization
Case postale 56 CH-1211 Genève 20 Switzerland
Internet
Printed in Switzerland

Copyright International Organization for Standardization
Provided by IHS under license with ISO
No reproduction or networking permitted without license from IHS

Not for Resale


‘

STD.ISO b03-b-ENGL

3799


4853903 O790072 097

@IS0

IS0 603-6:1999(E)

Foreword
IS0 (the International Organization for Standardization) is a worldwide federation of national standards bodies (IS0
member bodies). The work of preparing International Standards is normally carried out through IS0 technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. IS0 collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.
Publicationas an International Standard requires approval by at least 75 % of the member bodies casting a vote.
International Standard IS0 603-6 was prepared by Technical Committee ISOTTC 29, Small tools, subcommittee
SC 5, Grinding wheels and abrasives.
This first edition, together with IS0 603-1:1999 to IS0 603-31999 and IS0 603-7:1999 to I S 0 603-16:1999, cancels
and replaces ISO/R 603:1967, IS0 603-2:1981, IS0 1117:1975, IS0 2220:1972, IS0 2933:1974, IS0 3290:1976
and IS0 3921:1976 as a technical revision of these standards.

IS0 603 consists of the following parts, under the general title Bonded abrasive products -Dimensions:

- Part 1: Grinding wheels for external cylindrical grinding between centres

-

Part 2: Grinding wheels for centreless external cylindrical grinding


- Paft 3: Grinding wheels for internal cylindrical grinding

-

Part 4: Grinding wheels for surface grinding/peripheral grinding

-

Part 5: Grinding wheels for surtace grindingLface grinding

-

Part 6: Grinding wheels for tool and tool room grinding

- Part 7: Grinding wheels for manualt’y guided grinding

-

Part 8: Grinding wheels for deburring and fettling/snagging

- Part 9: Grinding wheels for high-pressure grinding

-

Part 10: Stones for honing and superfinishings

-

Part 11: Hand finishing sticks


-

Part 12: Grinding wheels for deburring and fettling on a straight grinder

-

Part 13: Grinding wheels for deburring and fettling on a vertical grinder

- Part 14: Grinding wheels for deburring and fettling/snagging on an angle grinder

-

Fart 15: Grinding wheels for cutting-off on stationary or mobile cutting-off machines

- Part 16: Grinding wheels for cutting-off on hand held power tools

--`,,`,-`-`,,`,,`,`,,`---

Copyright International Organization for Standardization
Provided by IHS under license with ISO
No reproduction or networking permitted without license from IHS

Not for Resale


STD-IS0 603-b-ENGL
INTERNATIONAL STANDARD

1999


4851903 0790073 T23 D
IS0 603-6:1999(E)

Q IS0

Bonded abrasive products

- Dimensions -

Part 6:
Grinding wheels for tool and tool room grinding

1 Scope
This part of IS0 603 specifies the nominal dimensions, in millimeters, of:

- Type 1: Straight grinding wheel (general applictaion and saw sharpening)
Type 3:Wheel tapered on one side

-

Type 5: Wheel recessed on one side

-

Type 6:Straight cup wheel

-

Type 7: Wheel recessed on both sides


-

Type 11: Taper cup wheel

--`,,`,-`-`,,`,,`,`,,`---

-

- Type 12:Dish wheel
These bonded abrasive products are intended to be used for grinding or regrinding of cutting faces and edges of tools.
The workpieces and the grinding wheels are mechanically guided.

2 Normative references
The following normative documents contain provisions which, through reference in this text, constitute provisions of
this patt of IS0 603.For dated references, subsequent amendments to, or revisions of, any of these publications do
not apply. However, patties to agreements based on this part of IS0603 are encouraged to investigate the
possibility of applying the most recent editions of the normative documents indicated below. For undated
references, the lates edition of the normative document referred to applies. Members of IS0 and IEC maintain
registers of currently valid International Standards.

IS0 525:1999,Bonded abrasive products

- General requirements.

IS0 6103:1999,Bonded abrasive products - Static balancing of grinding wheels - Testing.
IS0 13942:-l), Bonded abrasive products

-Limit deviations and run-out tolerances.


l)To be published.

1
Copyright International Organization for Standardization
Provided by IHS under license with ISO
No reproduction or networking permitted without license from IHS

Not for Resale


STD.ISO bO3-6-ENGL

L999

H 4ô5L903 0790074 9bT
Q IS0

I S 0 603-6:1999(E)

3 Dimensions
3.1 Type 1: Straight grinding wheel (general application)
See Figure 1 and Table 1.

--`,,`,-`-`,,`,,`,`,,`---

Figure 1 -Type 1
Table 1 - Dimensions of Type 1

3.2 Type 3: Wheel tapered on one side
See Figure 2 and Table 2.


I

Figure 2 - Type 3

D
80
1O0

T

H

J

U

5

13

40

1

6

20

50


I
I

175

I

10

I

I

200

I

13

I

250

85

32

~


1O0

14

2
Copyright International Organization for Standardization
Provided by IHS under license with ISO
No reproduction or networking permitted without license from IHS

63

Not for Resale

3


o IS0

IS0 603-6:1999(E)

3.3 Type 5: Wheel recessed on one side

See Figure 3 and Table 3.

Figure 3
Table 3

-Type 5

-Dimensions of Type 5


The value F is taken less than or eaual to half thickness T

3.4 Type 7: Wheel recessed on both sides
See Figure 4 and Table 4.
OP

1-

1-

R

7

Figure 4

D

T

H

300

50

76,2

400


65

127

-Type 7
P

150
215

G

R,

10

10

5

3

--`,,`,-`-`,,`,,`,`,,`---

Copyright International Organization for Standardization
Provided by IHS under license with ISO
No reproduction or networking permitted without license from IHS

F


Not for Resale


STDeISO b03-b-ENGL

4851703 077007b 732

1797

o IS0

I S 0 603-6:1999(E)

3.5 Type 1: Straight grinding wheel (saw sharpening)
See Figure 5 and Table 5.

Figure 5

- Type 1

Table 5 - Dimensions of Type 1
D

T

H

D


I

T

I

H

10

I

20

I

(31

250

8
10

32

13
16

20


ri
25
5

1

20

1

2

300

p
1
1
31
I 3.2 I

32

--`,,`,-`-`,,`,,`,`,,`---

200

32

4
Copyright International Organization for Standardization

Provided by IHS under license with ISO
No reproduction or networking permitted without license from IHS

Not for Resale


__

STD=ISO b03-b-ENGL

1999

W 4851903 0790077 b79 W

o IS0

IS0 60&6:1999(E)

3.6 Type 6: Straight cup wheel
See Figure 6 and Table 6.

I

I

I

I

OD


- 1

I

Figure 6

D

T

50
80
1O0

32

125

63

150
180

80
80

-Type 6
H


13

40

20
20
32

50

32

W

E
min.

5
6
8

8

10

8

13

10

16

16
16

See Figure 7 and Table 7.

t=

CbD

I

81

I
- 1

I

Figure 7
Table 7

-Type 11

- Dimensions of Type 11

--`,,`,-`-`,,`,,`,`,,`---

Copyright International Organization for Standardization

Provided by IHS under license with ISO
No reproduction or networking permitted without license from IHS

Not for Resale

5


--`,,`,-`-`,,`,,`,`,,`---

3.8 Type 12: Dish wheel
See Figure 8 and Table 8.
ØD

I=

I

w
I-

.

Ø K Ci-IIaI

+

i

t

d
I IØHI I

I

+4
I

Figure 8 - Type 12
Table 8 - Dimensions of Type 12

4 Designation

d)

dimensions;

e)

specifications of an internai nature;

, In accordance with IS0 525
and this part of I S 0 603

6
Copyright International Organization for Standardization
Provided by IHS under license with ISO
No reproduction or networking permitted without license from IHS

Not for Resale



STD-IS0 b03-b-ENGL
I

I

1999

4451703 0790077 441
IS0 603-6:1999(E)

0 IS0

5 Specifications
The specifications are left to the manufacture's discretion, see IS0 525.

5.1 Tolerances
Limit deviations and run-out tolerances in accordance with IS0 13942.

5.2 Balancing
Balancing is in accordance with IS0 6103.

5.3 Marking
Marking of bonded abrasive products is in accordance with IS0 525.

--`,,`,-`-`,,`,,`,`,,`---

7
Copyright International Organization for Standardization

Provided by IHS under license with ISO
No reproduction or networking permitted without license from IHS

Not for Resale


STD-IS0 b03-b-ENGL

1993

W 4853903 0790080 L b 3 I

o IS0

I S 0 603-6:1999(E)

Bibliography

[l] IS0 8486-1, Bonded abrasives - Determination and designation of grain size distribution - Part 7: Macrogrits F4
to F220.

--`,,`,-`-`,,`,,`,`,,`---

[2] IS0 8486-2, Bonded abrasives - Determination and designation of grain size distribution - Part 2: Microgrits
F230 to F1200.

Copyright International Organization for Standardization
Provided by IHS under license with ISO
No reproduction or networking permitted without license from IHS


Not for Resale


S T D - I S 0 603-6-ENGL 1799 m 4851703 0790083 OTT U
Q

I S 0 603-61999(E)

--`,,`,-`-`,,`,,`,`,,`---

ICs 25.1 00.70
Pricebasedon8pages

Copyright International Organization for Standardization
Provided by IHS under license with ISO
No reproduction or networking permitted without license from IHS

Not for Resale

IS0